Terms and safety notes

The short version: a plan is design guidance drawn from what you tell us. We have not seen your boat. You are responsible for checking what's really there and for the installation.

Last updated November 19, 2026

What a rigging plan is

A rigging plan is a set of drawings, a parts list and notes that describe one way to install and connect the marine electronics you told us about. It is design guidance.

It is built entirely from your survey answers, your photos and manufacturers' published information. Nobody from Rigging Bench has been aboard your boat, tested anything on it or seen anything you did not send us.

What it is not

It is not a marine survey, a safety inspection, a certification, an insurance document or a statement that your boat or any part of it is safe, compliant or seaworthy.

It is not a substitute for a qualified marine technician, and it is not a guarantee that the installation will work, fit or perform as you expect.

Assume your boat's wiring has a history

Most boats have had electrical work done many times, by many people, to many standards. Expect unlabeled wires, wiring left behind from equipment that was removed, splices and connectors that don't belong on a boat, circuits with no fuse or the wrong fuse, undersized wire, corrosion you can't see and colors that don't mean what they should.

A plan cannot account for conditions we were not told about or could not see in your photos. Treat every existing wire, fuse, switch, connection and device as unknown until you have traced and tested it yourself. Do not reuse existing wiring because the plan shows a wire in that location.

Red-flag notes and replacement suggestions

Where we notice something in your answers or photos that looks unsafe, out of place or worth replacing, we say so. Those notes are observations from limited information. They are not a complete list of what is wrong with your boat.

If something is not flagged, that does not mean it is safe. If something is flagged, we may be wrong about it. Use the notes as a starting point for your own inspection or a professional's.

Your responsibilities

You are responsible for the installation and everything that results from it, whether you do the work or someone else does.

Before you cut or drill: measure the actual equipment and the actual opening, confirm the cutout against the manufacturer's template, and check what is behind and under the surface. Cutting and drilling can't be undone, and dimensions in a plan depend on measurements you gave us.

Before you work on wiring: switch off and disconnect the batteries, and disconnect shore power.

Before you energize anything: confirm every fuse or breaker size and every wire gauge against the manufacturer's installation instructions for your actual cable lengths, check polarity, and check that every connection is tight and protected.

Follow each manufacturer's installation instructions and the applicable ABYC standards for boat electrical systems, including ABYC E-11. If a plan and a manufacturer's instructions disagree, follow the manufacturer and tell us.

Stop and call a professional if

You find melted, brittle, blackened or discolored insulation; wires or connections that are warm or hot; a burning smell; heavy corrosion at batteries, switches or bus bars; wires connected directly to a battery with no fuse; or signs of water in electrical connections.

You don't understand what a wire does, you can't find where it goes, or you are not confident doing any step.

A qualified marine technician, preferably ABYC certified, should correct those conditions before any new equipment is installed.

What plans do not cover

Shore power, inverters, generators, battery chargers' AC connections and any other AC wiring. AC on a boat can kill you and people in the water near the boat. That work belongs to a qualified marine electrician.

Fuel systems, engine wiring harnesses, steering, throttle and shift controls, and any structural change to the boat. Where a plan shows a connection to an engine or autopilot, it shows the data and power connections for the electronics only.

Lightning protection, bonding and corrosion systems, and compliance with any regulation, class rule or insurer's requirement.

Gasoline engines and fuel vapor

Electrical parts installed in spaces that can hold gasoline or propane vapor must be ignition protected. Do not install or relocate electrical equipment in engine, fuel tank or battery compartments unless it is rated for that space. If you are not sure whether a space qualifies, ask a professional.

Batteries, including lithium

Batteries store enough energy to start fires and cause serious burns. Follow the battery manufacturer's instructions for fusing, charging and mounting. Lithium batteries have requirements that differ from lead-acid, and the manufacturer's instructions for your specific battery take priority over anything in a plan.

Compatibility, parts and prices

Compatibility checks and part numbers come from manufacturers' published information at the time the plan is written. Manufacturers change products, connectors, software and part numbers without notice. Confirm compatibility and part numbers before you buy.

We do not control parts availability or pricing and are not responsible for parts you buy. Equipment recommendations are opinions based on what you told us.

Rigging Bench is not affiliated with, endorsed by or an authorized representative of any manufacturer named in a plan or on this site. Brand and product names belong to their owners.

Warranties and insurance

Installing or modifying equipment yourself can affect manufacturer warranties, your boat's warranty and your insurance coverage. Check with the manufacturer, your builder or dealer, and your insurer before you start.

No warranty, and limits on our liability

Plans, notes and recommendations are provided as is, without warranties of any kind, express or implied, including fitness for a particular purpose.

To the fullest extent the law allows, Rigging Bench and Viking E-Holdings LLC are not liable for property damage, personal injury, death, loss of use, lost time, consequential damages or any other loss arising from the use of a plan or from any installation, and our total liability for any claim is limited to the amount you paid for the plan.

By ordering a plan you accept these terms and agree that you use the plan at your own risk.

Refunds and corrections

If we can't produce a plan from the information you provide, you get a full refund.

Our promise: if a part on your list doesn't work with the rest as drawn, tell us within 30 days of delivery and we fix the plan. If we can't, you get your money back. Tell us through the contact page.

If a delivered plan contains another error we made, tell us and we will correct the plan. Otherwise, because a plan is custom work, the fee is not refundable once the plan has been delivered.

Founding price: the first five up-to-5-component plans are $99. We ask founding customers for an honest review of their plan. A review is never a condition of the plan, the promise above or a refund.

Your information and photos

You confirm that the information and photos you send are yours to share. We use them to build your plan and to answer your questions about it.

When you start the boat survey we keep your email, boat and what you want to add, so we can send you one reminder if you don't finish. We don't sell it or share it.

This site counts visits without cookies. If you arrive from a Google ad, Google's ad tag sets a cookie so we can see whether the ad led to a survey or an order. Its use is covered by Google's advertising policy.